Nova LED Light Harness - Product Info
Nova LED Light Harness - Product Info
Nova LED Light Harness - Product Info
- SIZING
- HOW TO FIT
- HOW TO USE
- CARE / MATERIAL
- in
- cm
Size
Girth
S
M
L
XL
18" - 22"
20" - 28"
25" - 35"
30" - 40"
Size
Girth
S
M
L
XL
45.5 - 56 cms
51 - 71 cms
63.5 - 89 cms
76 - 101.5 cms
- Stand your dog on top of a hard surface
- Use a soft measuring tape to measure your dog's girth (the widest circumference around your dog’s chest)
- Select the harness size from the chart above that best matches your dog's girth measurement
- If the measurement falls between two sizes, it's recommended to opt for the larger harness size to ensure your pet's comfort.
- Ensure lightbox is securely attached to harness back webbing using the wide mouth clip located on the back of the lightbox.
- Slide all four (4) light wand extensions into the wand casings of the harness. Important: Not all light wand extensions are the same length. To avoid damaging the want casings, refer to diagram.
- Open the buckle closures of the harness.
- Use the sliders to loosen the default settings on the neck, girth and chest straps.
- Put your dog's right front paw through the leg opening of the harness.
- Wrap harness around your dog’s back, closing the buckles on left side.
- Adjust the sliders so the harness fits snug but allows for 1-2 fingers of room between the straps and your dog’s body.
HOW TO USE
- Press bottom button once to turn on.
- Single press to switch between colours and light modes.
- To turn off, press and hold for 2 seconds.
HOW TO CARE
- The product contains a rechargeable lithium battery. Do not remove it from the product.
- Use the micro-USB cable provided to charge the light device (power adapter not included).
- Check the charging cable before use. Using damaged cables or chargers or charging when moisture is present can cause fires, electric shock, injury, death, or damage to property.
Make sure the charging cable is fully inserted into the power adapter when charging. - Charge product in a ventilated area at temperature between 50 F and 90 F (10 C and 32 C).
- The USB charging cord supplied with this product is standard with 5 V dc voltage and a current of .5 A or 500 mA.
LIGHT COMPONENT CLEANING INSTRUCTIONS
- To clean this product, remove the light component from the harness and use a damp cloth to clean it.
- Do not submerge the light component in water.
- Store product where ambient temperatures are within -4 F to 95 F (-20 C to 35 C).
HARNESS CLEANING INSTRUCTIONS
- Harness component can be machine washed on gentle cycle. Ensure buckles are fastened before placing in the washer.
RECYCLING INSTRUCTIONS
- Light component can be recycled at an electronic recycling centre at the end of product's life.
LIGHT COMPONENT CLEANING INSTRUCTIONS
- To clean this product, remove the light component from the harness and use a damp cloth to clean it.
- Do not submerge the light component in water.
- Store product where ambient temperatures are within -4 F to 95 F (-20 C to 35 C).
HARNESS CLEANING INSTRUCTIONS
- Harness component can be machine washed on gentle cycle. Ensure buckles are fastened before placing in the washer.
RECYCLING INSTRUCTIONS
- Light component can be recycled at an electronic recycling centre at the end of product's life.
Machine wash cold
do not iron
Hang to Dry
do not bleach
MATERIAL
BODY: 100% POLYESTER AIRMESH
WEBBING: 100% NYLON
UPPER LAYER: 100% POLYESTER
HARDWARE: ALUMINUM ALLOY
LIGHT CASING: PC (POLYCARBONATE)
BODY: 100% POLYESTER AIRMESH
WEBBING: 100% NYLON
UPPER LAYER: 100% POLYESTER
HARDWARE: ALUMINUM ALLOY
LIGHT CASING: PC (POLYCARBONATE)
×